Dual boot partitions your computer and installs one operating system in each partition.WARNING: Do not proceed with any of these steps unless you have the ability to restore a bare-metal backup. Each method has its own pros and cons, but you can install Windows as a dual boot system for free using Boot Camp Assistant. Thank goodness for good backups.The two best ways to run Windows on a Mac are dual boot systems and virtualization.This is one of the major problems faced after installing Mac os in the windows system. Dual Boot Mac OS Hackintosh and Windows 10. Triple Boot the Right WayDual Boot Mac OS Hackintosh and Windows 10 without Pendrive. I use a combination of Time Machine, CrashPlan, and Arq to back up my system, you should too.
![]() Dual Boot And Windows Mac Are Dual![]() There are several advantages to using Apple's process: Install Apple's Boot CampApple provides a supported method of installing Windows as a dual-boot option for Macintosh owners. However, several of the steps in that guide I didn't have to use at all, so I'm documenting my process here. Install rEFInd as a Boot Manager for all 3 OSesTo be fair, a lot of my instructions and the guide I initially followed, can be found here. Install Linux (I used Kali) into the newly freed space Use Windows 10 to shrink the Bootcamp partition, freeing up space to install Linux There is no way to install an earlier version of Windows using Boot Camp on newer hardware. Adjust if you wish, I used a 196GB partition for Windows 10, then split it into 128GB for Windows and 64GB for Linux (FYI, a Windows 10 installation with Office 365 installed takes up 68GB, so give yourself enough room under Windows).Note: Apple only supports Windows 8.1, or newer, for hardware released after 2014. You will have supported ways to control the Windows and macOS boot process on your MacBook from within Windows (via the Boot Camp Control Panel)Apple's official documentation for Boot Camp is found here.Follow Apple's instructions for installing Windows, but make sure you create the Windows partition approximately 64GB larger than what you want to end up with for Windows, that space will end up being given to Linux. Apple provides native drivers for the hardware under Windows Enter the size, in megabytes, by which to shrink the volume. Select the BOOTCAMP partition, right-click and select Shrink Volume Right-click on the Start Menu and select Disk Management Create Partition for LinuxFor the purposes of this article, I'm going to install Kali Linux, that's what I used, but installation with ANY version of Linux should work the same way.The first step is to shrink the Windows partition to make some space for Linux: Install rEFIndFor all macOS versions starting with El Capitan (10.11) Apple has enabled System Integrity Protection (SIP). Kali Linux, 64-bit, can be downloaded herePlace all of the rEFInd files (after unzipping) on a removable volume (SD Card, USB drive, or even a secondary HFS+ volume) so you can use it in the next step. I also have an SD card mounted.The shrinking process took a LONG time (~30 minutes), don't worry about it, let it run to completion and do not interrupt.After the Volume shrinking process is completed, it's time to download some files to perform the installation however, you probably want to do this under macOS, so first boot back to your macOS volume and the download them both: Find the volume where you have rEFInd stored (start with ls /Volumes) Once in Recovery mode select Terminal from the Utilities menu Reboot the computer and hold down Command-R Make sure the rEFInd files are available on a drive that macOS can see and use, then follow these instructions: In order to install rEFInd you will have to boot into Recovery. That means that you cannot install rEFInd directly on drives where SIP is enabled. Use with caution or update the components in the theme with the newer versions. At the time of this article's original publication, they were both the same version, but now, 3 years later, the theme's version of rEFInd is woefully outdated. You probably shouldn't do that, though your milage may vary on getting this to work. Upate 20200906: This theme's installation instructions ask you to "replace the EFI folder" in the rEFInd install you just did, it ALSO replaces the more curent version of rEFInd and the cryptographic keys that were provided. I used the OSX Standard Theme 1.0 found here. You will still get a warning that SIP is enabled, but you can ignore it (SIP is enabled on the boot volume, but you're not installing it thereFull installation instructions can be found on the rEFInd site.You may also want to theme rEFInd to look more "mac-like". Install Linux#Boot into macOS and have a USB key available to be reformatted, it can be pretty small (small works better), an 8GB drive is perfect.In order to create a bootable USB drive, you can use the Terminal: You can then configure rEFInd to ignore some volumes, but save that for after you have everything working properly. They probably all won't be bootable, through trial-and-error you should be able to find the correct macOS and Windows 10 volumes. Just reboot and you should be taken to the rEFInd boot menu, from there you should be able to boot into either macOS or Windows 10.Note: rEFInd will automatically find what it believes to be bootable volumes. Run the command: dd -if=kali-linux-2016.1-amd64.iso -of=/dev/disk2 bs=1m Find your USB key by running: diskutil list, note the drive name, e.g. Kali-linux-2016.1-amd64.iso Change the directory to where you downloaded the ISO for your Linux installation, e.g. You can then insert your USB drive, then hit ESC to refresh the volumes and you should see the Linux installation drive appear. However, if you reboot now, you'll see the rEFInd boot menu. The reason you had to install rEFInd before installing Linux was that, in my experience, I could not get the standard macOS boot manager to recognize the USB drive I had prepared with Kali Linux. Once it finishes you should have a bootable USB key for Kali Linux (or whatever)Alternatively, if you want a graphical imaging process, you can use UNetbootin as documented here for Ubuntu (just use Kali or whatever image you want).You're now ready to install Linux. Find mac address of usb ethernet adapter for macbookJust follow the instructions and re-install rEFInd again and it should come back and allow you to boot again. Using rEFInd you can select the appropriate OS and it should boot cleanly on your hardware.In the event that rEFInd gets clobbered (you'll know, because a power-cycle takes you to the built-in macOS boot manager) you should still be able to boot into Windows, but you'll probably lose the ability to boot into Linux. CompletedYou should now have a triple-booting MacBook Pro.
0 Comments
Leave a Reply. |
AuthorMark ArchivesCategories |